Inner Tube Repair

How to fix a flat on a bicycle inner tube, using a pre-glued patch or vulcanizing patch.

1

Locating the Hole

What do I need to know how to do?
What Tools do I need?

To fix a flat, first locate the hole in the inner tube. If possible, re-inflate inner tube to at least twice its normal width.

Tube Removal 4 Overinflate

Inspect for air leaks by holding tube close to the sensitive skin of lips or by holding tube near your ear to hear leaks. Move the tube around its circumference. If these steps do not work, submerge tube in water and watch for bubbles at the hole.

Tube Removal 5 Hiss Listen

Tube Removal 5 Bubbles

2

Preliminary steps

Once you have found the hole, use a marking pen to mark it. Make four marks, one to each side of hole. Do not mark close to hole, as the mark may be sanded off.

Tube Removal 6 Mark Hole

To prepare the tube for patching, clean the tube by lightly abrading area around hole. Most patch kits include a small piece of sandpaper, but a separate piece of sandpaper or fine emery cloth is also acceptable. Excessive sanding or heavy pressure can cause grooves in the rubber, which may lead to patch failure.

Patch 1 Sandpaper In Progress

Patch 1 Sandpaper Sanded

If possible, clean the area using a clean rag and alcohol, or any solvent that doesn’t leave a film. Allow the area to dry completely.

Patch 2 Clean W Alcohol
3

Patching an Inner Tube Using the GP-2 Super Patch Kit

The GP-2 Super Patch Kit uses pre-glued patches. There is no tube of glue.

  1. Peel the patch from its backing. Handle the patch as little as possible and only by the edges.
  2. Center the patch to the hole and lay the patch on the tube.
Patch 3 Lay Patch
  1. Apply pressure to the patch to assure a proper seal. Roll the patch and tube between thumbs and forefingers.
Patch 4 Press Patch
  1. The tube is ready to install. DO NOT test the patch by inflating the tube while outside of the mounted tire. This may stretch the tube body and weaken the patch bond.
This tube was overinflated after the installation of a pre-glued patch
This tube was overinflated after the installation of a pre-glued patch
4

Patching an Inner Tube Using the VP-1 Vulcanizing Patch Kit

Glue-on style patches such as the VP-1 Vulcanizing Patch Kit require the application of a thin layer of self-vulcanizing glue on the tube before the patch is applied.

  1. Open the glue tube and puncture the seal. Apply a thin coat of glue and spread it evenly around the area of the puncture, slightly larger than the patch size. Use a clean finger or the back of the patch to spread the glue evenly in a thin layer. Do not apply too much glue - the glue layer should not appear “glopped” on.
Patch 6 Spread Glue
  1. Allow the glue to dry. This may take several minutes. Test by touching only the perimeter area of glue, not where the patch will contact.
  2. Peel the patch from its backing. Handle the patch only by its edges
  3. Center the patch to the hole and lay the patch on the tube
Patch 7 Peel Vp 1
  1. Apply pressure to the patch, especially at the edges
  2. If possible, maintain pressure for over a minute
Patch 8 Press Vp 1
  1. After a minute or two, inspect the bond of the patch to the tube, verifying that all the edges look adhered to the tube surface
Properly bonded patch

Properly bonded patch

Improperly bonded patch

Improperly bonded patch

  1. Leave the clear plastic cover on the patch
  2. Mount the tube inside the tire and inflate

NOTE: Leaving on the cellophane cover over the patch will allow the patch to slide inside the tire and reduce stress on the fresh patch. If the cellophane is removed, use a dusting of talc or baby powder over the patch.

5

Temporary Repair of Tire with TB-2 Tire Boot

If a tire has been ripped and the casing damaged, it may not hold an inner tube. It is possible in some cases to make a temporary trailside repair with a tire boot such as the TB-2. A booted tire should not be considered a permanent repair. The tire should be replaced as soon as possible.

tb2 b
  1. Locate the rip in the tire. Compare the rip to the size of the tire boot. The tire boot must completely overlap the rip to be effective.
  2. Wipe the inside of the tire clean adjacent to the rip.
  3. Peel the backing off the boot (this is the side opposite of the logo).
  4. Align the patch so the edges do not extend beyond the tire bead. If necessary, cut the boot so it does not extend past the tire bead.
  5. Center the patch to the rip and press the patch to the inside of the casing.
TB-2

NOTE: Always replace ripped tires as soon as possible.