| Tool Description |
Park Tool Product
or possible tool source | More Information
|
| Bicycle Repair Stand |
See Repair Stand Catagory |
The stand forms the base of a good shop. |
| Sockets and Bit set |
Park Tool SBS-1 |
3, 4, 5, 6, 8 and 10mm hex bits T25, T30 and T40 Torx® style bits
9, 10, 11, 12, 13, 14, 15mm and 1” sockets |
| Torque Wrench, smaller torques |
Park Tool TW-1 or TW-5 |
For use on small threads, such as derailleurs and brakes |
| Torque Wrench 0-600 inch lb. |
Park Tool TW-2 or TW-6 |
For use on medium and large thread, such as stems & cranks. |
Hex Wrench Set
|
Park Tool AWS-10, or HXS-1 |
|
| Work Apron | Park Tool SA-1 or SA-3 | Keep your clothes clean and hold those tools while you work |
| Screwdriver 3/16" straight blade tip |
Park Tool SD-6 |
|
| Phillips tip screwdriver, #2 (1/4") |
Park Tool SD-2 | |
| Screwdriver, 1/8 straight blade tip |
Park Tool SD-3 | |
| Hammer |
Park Tool HMR-2 |
Double ended, steel and rubber |
| Combinations Wrenches |
Park Tool MW-SET | Box end with open end on other side. |
| Large 12" Adjustable Wrench |
Park Tool PAW-12 | For odd sizes locknuts. |
BOTTOM BRACKET TOOLS |
| Lockring Wrench |
Park Tool HCW-5 |
Fits most all lockring types for adjustable square BB's |
| Adjustable Cup Tool, hinged, heavy duty | Park Tool SPA-6 | Adjustable type bottom brackets |
| Fixed Cup Tool, 36mm | Park Tool HCW-4 | Adjustable type bottom brackets |
| Fixed Cup Wrench Clamp
| Large bolt, 2 washers & 2 nuts, or HHP-2 | Adjustable type bottom brackets |
|
Cartridge BB Tool |
Park Tool BBT-22 | Fits 20 tooth internal spline cups such as on Shimano® cartridge bottom brackets, FSA®, and Race Face® ISIS Drive bottom brackets |
| Bottom bracket external bottom bracket cup wrench | Park Tool BBT-9 | Shimano® Hollowtech II, Race Face® X-type, andTruvativ Giga X-Pipe crankset systems |
| Bottom bracket lockring tool | Park Tool BBT-7 | Shimano XTR & Dura-Ace lockrings (adjustable type bottom brackets) |
| Crankset & bb tool |
Park Tool BBT-18 | Fits Shimano® bb's with 8 notches, Truvativ® and Bontrager®. Also for cassette type chainrings |
HEADSET TOOLS |
| Headset Locknut Wrench (32mm and 36mm)- threaded headsets only | Park Tool HW-2
or large adjustable wrench PAW-12
| 32mm and 36mm open end wrench in 8-point. Wrench wraps to fit all points. |
| Headset Lower Race Wrench (32 & 36mm) | Park Tool HCW-15 | For threaded steering columns |
HUB TOOLS |
| Axle Vise |
Park Tool AV-1, AV-4. | Holds axles without damaging threads |
| Cone Wrenches | Park Tool SCW-SET Shop cone wrench set | For some hub models, 2 wrenches required of 13, 14, 15 or 16mm. |
WHEEL AND TIRE TOOLS |
| Truing Stand |
Park Tool TS-2 | Speed repair of wheels |
| Truing Stand Base for TS-2 | Park Tool TSB-2 | Tilting base for TS-2 |
| Spoke Tension Meter | Park Tool TM-1 | Check tension on spokes |
| Wheel Dishing Tool | Park Tool WAG-4 | |
| Spoke Wrenches |
Park Tool SW-0, SW-1, SW-2 |
Select smallest size that fits. |
| Tire Levers |
Park Tool TL-1, TL-2 or TL-5 (steel)
|
Levers vary in design and fit. |
| Patch Kit | Park Tool GP-2, VP-1 | VP-1 has glue in tube. GP-2 has pre-glued patches.
|
| Floor Pump | PFP-3 Pump | Pump head fits both presta and schrader |
| Spoke Ruler | Park Tool SBC-1 | Measures spoke length and ball bearings sizes. |
DRIVE TRAIN TOOLS |
| Pedal Wrench | Park Tool PW-3 or PW-4 |
PW-3 has 15 & 9/16". PW-4 has 15mm only. |
| Crankarm Pullers |
Park Tool CWP-7CCP-44 or CCP-22
| CCP-4 is for round, splined ISIS Drive® or Shimano® Octalink only.
CCP-2 is for square type spindle only.
CWP-6 works with either square or round spindles. |
| Cassette/Freewheel Removers | Cassette / Freewheel Category |
Purchase as needed. |
Sprocket Removal Tool- chain whip
|
Park Tool SR-1 |
Needed to hold cassette while lockring is removed. Note: older freehubs required two sprocket tools. |
| Chain Rivet Extractor | Park Tool CT-3
|
Compatible with 10 speed chain systems. |
| Chain Wear Checker | Park Tool CC-2, or CC-3 | Check chain for wear |
| Drive Train Cleaning Kit | Park Tool CG-2 | Include Cyclone Chain Cleaner CM-5, gear brush GSC-1 and ChainBrite fluid. |
| Derailleur Alignment Gauge | Park Tool DAG-1 | Aligns rear derailleur hanger |
BRAKE TOOLS |
| Fourth Hand Tool | Park Tool BT-2 | Tightens cable slack by pulling cable. |
| Cable Cutters | Park Tool CN-10 | Cuts both cable and housing |
